Full Leak Diagnosis
Attic moisture mapping plus an exterior inspection of flashing, valleys, ridge vent and penetrations. You get photos of the failure point and a plain explanation of why it leaked, not just where.
Every repair we sell covers the full job: diagnosis, materials, labor, cleanup and a water test. You are not paying extra for the inspection that found the leak. If the repair uncovers rot or structural damage that changes the scope, we stop and re-quote before continuing, so nothing gets added to your bill without your approval.
Attic moisture mapping plus an exterior inspection of flashing, valleys, ridge vent and penetrations. You get photos of the failure point and a plain explanation of why it leaked, not just where.
New underlayment, ice and water shield, roof flashing and matching shingles installed to manufacturer spec. We use GAF, Owens Corning and CertainTeed products so the repair carries real material coverage.
Fresh roofing cement at every penetration, new drip edge where it has corroded, and shingles set with a roofing nailer at the correct nail pattern. No hand-tacked shortcuts that blow off next winter.
We run water over the repaired section and watch it from inside the attic. If any moisture shows up, we keep working. You do not pay for a repair that has not been proven dry.
Old shingles, nails and debris go with us. We magnet-sweep the driveway and walkways for stray fasteners and clear your gutters of the material we removed. You should not be able to tell we were there, except for the dry ceiling.
Roof leak repair in New York is the diagnosis and permanent sealing of water entry points on an existing roof, not a patch-and-pray job. We pull the failed shingles, cut back wet underlayment, replace rusted roof flashing, and rebuild the ice and water shield around chimneys, valleys and vent stacks. Every repair gets new roofing cement, fresh drip edge where it has corroded, and a water test on the spot. If the decking underneath has gone soft, we replace that too, because a leak you can see usually means rot you cannot.
New York roofs take a beating that few states match. Nor'easters drive rain sideways into flashing, February ice dams back meltwater under shingles, and summer hail cracks asphalt shingles that were already at the end of their life. That is why we treat every call as a diagnostic first. Homeowners searching for roof leak repair near me in New York usually have three things in common: a brown ceiling stain, a musty attic smell, and a leak that only shows up after heavy rain. We find it, we fix it, and we show you the photos.
Five steps, no mystery. Here is exactly what happens from the moment you call until the leak is gone and tested.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Moisture meter
Reads dampness inside the roof decking and insulation so we can map the water trail from the attic side before we ever climb the roof.
Roofing ladder and safety harness
Gets our technicians onto steep pitches safely and keeps them anchored while they work. OSHA-compliant setup on every job, no exceptions.
Pry bar and utility knife
Lifts and cuts back failed shingles and underlayment without damaging the surrounding courses, so the repair blends into the existing roof.
Roofing nailer and roofing hammer
Sets new shingles at the correct nail pattern and drives hand nails in tight spots around flashing and valleys where a nailer will not fit.
Chalk line and shingle cutter
Keeps new courses straight and cuts shingles to fit around chimneys, vents and ridge lines for a clean, code-correct finish.
Roofing torch
Used on modified bitumen and low-slope repairs to heat and seal membrane seams properly instead of relying on adhesive alone.
Attic-first diagnostics
We start inside with a moisture meter and work outward. Water enters at one point and shows up somewhere else, so mapping the trail from the attic saves time and prevents us from repairing the wrong shingle.
Manufacturer-spec flashing detail
Every flashing repair is built to GAF and Owens Corning installation standards, including proper ice and water shield coverage and drip edge placement. That is what makes the repair eligible for material warranty coverage.
Water testing before sign-off
We run water over the repaired area and watch it from inside. A repair is not finished until it has been proven dry under live water, not just visually sealed.
Photo documentation
Before and after photos of every repair go into your file. You see exactly what failed and what we did about it, and you have a record if you ever sell the home or file a claim.
01
What we do: We treat this as an active leak and prioritize it. A technician inspects the attic and roof the same day, finds the entry point, and completes the repair in a single visit whenever the weather allows.
→ The leak is sealed before the next storm, and the ceiling stain stops growing. You get photos of the repair and a written warranty.
02
What we do: We tarp any open area immediately to stop water intrusion, then schedule the permanent repair. Missing shingles get replaced with matching material, and we check the surrounding courses for wind uplift.
→ Your roof is watertight again within days, and the repair matches the rest of the roof so it does not look patched.
03
What we do: We repair the TPO membrane seam, reseal the parapet flashing, and adjust the drainage so water moves off the roof instead of sitting on it. Ponding water is a drainage problem as much as a membrane problem.
→ No more standing water, no more seam leaks, and the membrane lasts years longer than it would with the ponding left alone.
04
What we do: We perform a documented inspection, identify whether the leak was repaired correctly, and fix anything that was not. You get a written report with photos that satisfies a buyer, a seller or an attorney.
→ The transaction moves forward with the roof issue resolved and documented, instead of becoming a negotiation problem.
New York roofs fail differently depending on where you are. Along the coast, from Long Beach to Mastic, salt air corrodes flashing and fasteners faster than inland, and wind-driven rain pushes sideways into every seam. Inland and upstate, the freeze-thaw cycle is the main enemy: water gets into a hairline crack, freezes, expands, and opens it wider by spring. Ice dams form on north-facing eaves from Westchester up through Putnam and Dutchess counties, and they are the number one cause of repeat winter leaks. Building stock matters too. Brooklyn and Queens have thousands of flat roofs with parapet walls and internal drains, while Long Island is mostly asphalt shingle on pitched roofs with valleys and dormers. We carry materials for both, and our trucks are stocked with TPO membrane, ice and water shield, and matching shingles so most repairs finish in one visit. If you need roof leak repair services in New York after heavy rain, we route crews by region so nobody waits days for a tarp.
Brooklyn
Flat roofs and parapet walls dominate here, and ponding water is the most common leak cause. We repair TPO seams and correct drainage pitch on brownstones and multi-family buildings.
Huntington
Pitched asphalt shingle roofs with dormers and valleys. Wind uplift after nor'easters is the typical failure, and we replace lifted shingles with matching material.
Mount Vernon
Older homes with original flashing details that have corroded. Ice dams in February back water under shingles, so we rebuild eaves with fresh ice and water shield.
Long Beach
Salt air accelerates corrosion on flashing and fasteners. We use corrosion-resistant materials and reseal penetrations more aggressively on coastal properties.
Nor'easters driving rain sideways into flashing
Wind-driven rain finds gaps that ordinary rainfall never reaches. We seal flashing with cold-weather-compatible roofing cement and check every penetration after a major storm.
Ice dams on north-facing eaves
Meltwater backs up under shingle courses and leaks into walls. We install ice and water shield at the eaves and correct attic ventilation to stop the dam from forming.
Coastal salt air corrosion
Flashing and fasteners rust through years earlier than inland. We spec corrosion-resistant materials on coastal jobs and inspect them more frequently.
Flat roof ponding water
Standing water works through TPO seams and shows up as leaks in multiple units. We repair the seam and correct the drainage pitch so water actually leaves.
Most leaks fall into a handful of categories, and each one has a specific fix. Here is what we see most often and how we handle it.
Problem
Each wet cycle soaks insulation and drywall, and mold can start within 48 hours of sustained moisture. The longer it runs, the more interior repair you are paying for on top of the roof.
Our Fix
We trace the water trail from the attic side with a moisture meter, then confirm the entry point on the roof. Once we seal the actual breach with new flashing and underlayment, the stain stops spreading and the ceiling can be repaired.
Problem
Meltwater pools behind the dam and pushes under shingle courses, leaking into exterior walls and ceilings. It is the single most common cause of repeat winter leaks in Westchester and Putnam counties.
Our Fix
We rebuild the vulnerable eaves with fresh ice and water shield and correct the attic ventilation that feeds the dam. The repair is detailed for freeze-thaw cycles, so it holds when temperatures swing from 40 degrees to 10 overnight.
Problem
Standing water finds every weak seam in a TPO membrane. Left alone, it works through the deck and shows up as leaks in multiple units of a building at once.
Our Fix
We reseal failed seams, repair parapet flashing, and correct the drainage pitch so water leaves the roof. For Brooklyn and Long Beach flat roofs, that combination stops the leak and prevents the next one.
Problem
Wind uplift lifts shingles and breaks their seal without tearing them off. The damage is invisible from the ground until the next heavy rain finds it, often weeks after the storm.
Our Fix
Our post-storm inspections check every course for lifted shingles and cracked ridge caps. We re-seal or replace what failed and document the damage with photos, which also helps if you are filing an insurance claim.
A roof leak gets worse every time it rains. Here is what you get when you put our crew on it instead of waiting for the next storm.
Same-Day Leak Diagnosis
Call before noon and we are usually on your roof the same day. We inspect the attic first, then the exterior, because interior staining tells us which slope is guilty. You get a written finding with photos, not a vague guess about where the water might be coming from.
Storm-Ready Emergency Crews
After a nor'easter or a hail event, we run emergency roof leak repair New York routes across the region. Tarp-overs go up the same day to stop interior damage, then we schedule the permanent repair. That two-step approach saves ceilings, insulation and hardwood floors.
Repairs Built for NY Winters
We install ice and water shield at every penetration and re-seal with cold-weather-compatible roofing cement, so the repair holds through freeze-thaw cycles. Ice dams are the number one cause of repeat leaks in Westchester and Putnam counties, and we build the fix to beat them.
Flat and Low-Slope Experience
Brooklyn and Long Beach have thousands of flat roofs with ponding water problems. We repair TPO membrane seams, reseal parapet flashing, and correct the drainage pitch so water actually leaves the roof. Flat roof leaks do not fix themselves, and a bucket in the hallway is not a strategy.
Typical 2026 pricing for residential roof leak repair in New York runs $350 to $1,200, with most jobs landing around $600. Simple flashing reseals sit at the low end; valley rebuilds, chimney flashing replacement and flat roof membrane repairs push toward the high end. Emergency tarp-overs add $250 to $500. We give you a flat written price before work starts, so the number you approve is the number you pay. If you want the best roof leak repair in New York at a fair price, get the diagnosis first and the price second.
Typical Investment Range
$350 - $1,200 for most residential repairs; $500 - $1,500 for flat roof membrane work
A $600 repair that stops a leak protects thousands of dollars of insulation, drywall and flooring. It also buys you time before a full replacement is truly necessary, which is the cheapest path for most homeowners.
What changes the price
Leak location and access
A leak near a valley, chimney or skylight takes longer to repair than a simple pipe boot. Steep pitches and multi-story roofs also add labor time because of the safety setup required.
Roof type and material
Asphalt shingle repairs are the least expensive. TPO membrane, modified bitumen and cedar shake repairs cost more because they need specialized materials and techniques like torch-applied seams.
Extent of hidden damage
If the leak has rotted roof decking or soaked insulation, that material has to be replaced before the repair will hold. We show you the damage and re-quote before continuing.
Emergency vs. scheduled
Active leaks that need an immediate tarp or after-hours response carry an emergency premium. Scheduling the permanent repair during normal hours keeps the cost lower.
Number of leak points
One leak is straightforward. Three or four separate entry points across different slopes take more diagnostic time and more material, and the price reflects that honestly.
Google ★★★★★4.9
Found a leak two other companies missed. Rebuilt the flashing around our chimney and the ceiling has been dry all year. Fair price, showed up when they said they would.
Yelp ★★★★★4.8
Tarped our roof the same day after a storm and came back to do the permanent repair. Photos of everything, no surprise charges. Exactly what you want from a roofer.
BBB ★★★★★4.9
Flat roof leak in a rental unit. They resealed the seams and fixed the drainage so water stops ponding. Tenants stopped calling me about drips. Worth every dollar.
Our technicians carry New York State Home Improvement Contractor licensing, OSHA safety certification, and manufacturer credentials including GAF Master Elite and Owens Corning Preferred Contractor status. That matters because manufacturer-certified installers can offer stronger material warranties than uncertified crews, and the work is inspected against the same standards the manufacturers set. We repair asphalt shingle, TPO membrane, modified bitumen and cedar roofs across the state, and we document every job with photos so you can see exactly what was done.
Our roof leak repair contractor New York crews cover the whole state, from the Hudson Valley down through Long Island and into all five boroughs. Every city below gets the same diagnostic process, the same flat pricing, and the same written warranty. If your town is not listed, call us anyway. If we cannot reach you, we will tell you straight and point you to someone who can.
Historic homes near the Hudson with older flashing details. We repair slate and shingle leaks and rebuild corroded flashing to match the original profile.
South Shore salt air corrodes fasteners faster here. We reseal penetrations with corrosion-resistant materials and check every pipe boot and vent stack.
Flat roofs, parapet walls and ponding water are the norm. We repair TPO seams, reseal parapet flashing and correct drainage pitch on brownstones and multi-family buildings.
Wooded lots mean debris-clogged valleys and gutters. We clear the blockage, repair the damaged shingle courses and reseal the valley flashing.
Pitched shingle roofs with dormers and valleys. Wind uplift after storms is the common failure, and we replace lifted shingles with matching material.
Older homes with original flashing that has reached the end of its life. We rebuild step flashing and counter-flashing around chimneys and sidewalls.
Hilly terrain and freeze-thaw cycles open hairline cracks in flashing. We seal with cold-weather-compatible cement and replace ice and water shield at the eaves.
Commercial and residential mix with flat and pitched roofs. We handle TPO membrane repairs and shingle leak repairs on the same route.
Nor'easter wind uplift is the typical call here. We tarp open areas the same day and replace damaged shingle courses with matching material.
Large wooded properties with debris-heavy valleys. We clear the valleys, repair the flashing and water-test the repair before leaving.
Coastal salt air and flat roofs. We repair membrane seams, reseal parapet flashing and spec corrosion-resistant fasteners on every job.
South Shore storms drive rain sideways into flashing. We reseal every penetration and check ridge vent and drip edge for wind damage.
Rural and riverside homes with older roofs. We diagnose leaks carefully and repair what can be repaired before recommending replacement.
Older building stock with ice dam problems in winter. We rebuild eaves with fresh ice and water shield and correct attic ventilation.
Suburban shingle roofs with chimney and skylight leaks. We rebuild flashing, replace failed underlayment and water-test the repair on site.
Real answers to the questions we hear most often from local homeowners and property managers.
When a leak has compromised too much of the deck to repair, new installation with fresh underlayment and ice and water shield is the durable answer. We install GAF and Owens Corning Duration systems built for New York weather.
View Roof InstallationA roof that leaks in three places is usually telling you it is done. Full replacement removes the rot, corrects the flashing details that failed, and resets your warranty clock. We handle tear-off, disposal and permits.
View Roof ReplacementBeyond leaks, we repair wind-uplifted shingles, cracked ridge caps, failed pipe boots and damaged drip edge. If your roof is structurally sound but locally damaged, a targeted repair beats a replacement every time on cost.
View Roof RepairA 21-point inspection catches flashing failure, clogged gutters and early shingle wear before they become ceiling stains. We document everything with photos. It is the cheapest way to avoid a mid-winter emergency.
View Roof InspectionAnnual maintenance clears debris, reseals penetrations and checks attic ventilation. Homes on this plan see far fewer leaks, because most failures start small and announce themselves early if someone is looking.
View Roof MaintenanceActive leaks, storm damage and downed tree limbs get priority dispatch. We tarp, stabilize and document the damage the same day, then schedule the permanent repair once the weather clears.
View Emergency Roofing ServicesCall (833) 829-2623 any time, day or night. Our phone is answered around the clock for emergency leaks and storm damage, and standard estimates are booked within 24 to 48 hours. You can also email [email protected] with photos of the problem and we will get back to you the same business day.
Phone
(833) 829-2623Address
New York
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available